Hi similar problem I now get read errors on lots of tiffs (large ones) that was ok in previous versions. I did shift analize settings and get 2000/1830/1465 Is this low? I have 16gb of ram installed is QU only able to use 2gb?
Thanks Phill

Hi I had been thinking it nay be to do with the page size I set it up on. Like you say mine is very simple to recreate. Yes forward planning from now on I suppose. 
Thanks very much for your help as always very clear.

Regards Phill

images would be a good idea! 

Hi ok here are my screen shots and settings.
(1)layout.jpg is the layout after running it and inserting images. centre picture is 213mm smaller pictures are 71mm square. making a print size of approx 355mm. This is on 44inch wide paper.
(2)layout images.jpg is the layout run with images inserted after been recalled. All seems ok upto now
(3)after size change.jpg is the dialoge box telling me it it going to resize the job as it wont fit the print sheet size after changing paper size to 24"  (at this point i had already clicked no and just took this screen shot to show the dialoge box) and this is what happens. no layout with pictures
(4) After yes.jpg is what happens to my layout after selecting yes to resize to fit paper. layout has been reduced in size. and not the size i want


So why Is qi telling me that the layout wont fit on 24" when the job is only 355mm square in size and my 24" paper is 600mm ish?
I know I probably doing something very wrong I usually am and that it's not qi thats at fault. I tried changing the paper size to 24" before running the layout but was told it was the wrong size and would not fit.
and notice in(3) after size change.jpg that the images are still in the queue and there is no image or layout anywhere there is only this page.

I wait in Embarrassment at the reply.
Phill

Hi I created a layout and run it all is fine. I add images and save it as a job later I recall the job. When I made it I did it on 44" wide paper but this is far too big for the print so I decided to put a differant sheet size in i.e 24" the layout should fit on this size but qi is telling me it will not and wants to scale the layout to fit the new sheet size.If I tell it not to scale there is nothing in the print area if I say yes scale then it makes it much smaller. Is this a Limitation of using a layout or am I doing something wrong?
I have prob not given enough info here but I am unsure what else you may need to know. Or i don't make sense(this is likely)!
Thanks Phill

Hi I just had a I/O error when I ran a layout I had saved and qi would not shut down and just kept coming up with this error. So I killed it in taskmanager so as usual when I next started qi up it said not shut down correctly do you want to reset settings or normal. So I clicked normal (well I though I had!) and it started up but all my settings where gone. Do I have to set everything myself again or is there a way to get them back?
Thanks Phill

Hi Mike, got it almost strait away I used to love the stereo gram books of the 90's. This is the first time I have seen this type of 3d it looks great.
Phill

I thought this was the case but it did seem a bit confusing never mind always happy to pay for good products so will purchase the profile when it becomes available canon 550d sorry if
Phill

Ok I am a bit behind here  So when I puchased QU do I get the camera profiles free? Do I need to e-mail Mike? Sorry this is probarbly explained somewhere but  I can't find it.
cheers Phill.

Great tip Terry thanks.

Hi Terry thanks for that I knew I would be doing something wrong as usual! Gosh its so easy to create great layouts this one one just a experiment for a canvas who's wrap was images around the edge. I mostly do canvas prints and find q very easy. One thing i was asked to day was could I apply different effect to each side i.e mirror on one edge and wrap on the other, as some  images are not suitable for certain wraps I can get round it in photo shop. But to my understanding this is not possible in q.

many thanks for your help

Phill

Hi I wonder if anyone can help me.I have created this layout and saved the job and also saved it as a layout. Now when I recall the job as just settings it does not come back as the layout instead it comes as
a layout of the small pictures round the edge as a layout. So thought if I "run" it as a layout through custom in the print properties it would come up with this layout without the images in, is there a way to get the layout to load without the images so I can just drop new images in to the layout or am i doing it all wrong?Or is it not possible? Any advice is very much apreciated I am a new user to qimage and decided to buy ultimate after using the trial and wonder how I managed without it!!

Phill