You can already do that with a cutout/frame.  There are some included with Qimage but you can create your own that have any style including drop shadows, wooden frames, etc.

https://www.ddisoftware.com/qimage-u/help/function.htm#cutouts

Regards,
Mike

Hello,

Would it be possible to add an option where the color of each side of a photo mat can be defined. Currently only the width can be defined individually but the selected color applies to all sides.

This would allow to add sort of a 'digital' picture frame passepartout around the image (instead of a card board). For example two sides in white and two in light grey (shadow). I can then add a thin black line around it (second mat). 

I've seen people doing that in Photoshop (probably a macro) but I don't want to pass every image through PS before printing.

Christian

I've set-up two unclog 'jobs' for a certain day/time.
But "out of the blue" will there be a 'unclog job', without a command. I notice, that in the 'footer' is an incorrect day/time stemp. I have running a small piece of software, synchronized the OS time each 30 minutes. [Network Time Synchronization]

Has anybody an explanation? My PC is 24/07 on & QI is running in the background (System Tray).

With regards, Martin.
from the Netherlands
 

QI Ultimate v2025.102. Epson SC-F570 printer. Win10 64bit

When I attempt to run the unclog utility, it automatically changes my printer paper Source settings from AutoSheetFeeder to Roll paper. Never noticed this before and certainly don't want to print unclog patterns on 24" roll paper. Is there a setting I've missed?

Update - rebooted, same issue and tried with my Epson SC R2400 - same issue, switched paper source from Sheet to Roll.

Update - solved. Missed the setting when choosing the printer within unclog setup.

Roger that.
Thanks

I think the Prism software is doing its job well and the results will only be as good as the target and its calibration file. The status of Faust is now iffy at best, but they seemed to have produced good results in the past. The previously mentioned UK supplier is very responsive, but I question the accuracy of their data files. It would seem the best answer is a scan of the specific target you're using and that would appear to be available here- https://www.chromix.com/colorgear/product.cxsa?toolid=434

IT-8 targets aren't that easy to get. The Silverfast/Lasersoft target from B&H appears to be a new style target and I suspect that's not compatible with Prism unless Mike says otherwise.
https://www.bhphotovideo.com/c/product/1667496-REG/lasersoft_imaging_la1208_silverfast_3_93_x_5_90.html

More in the distant future if I can get both my old and new targets rescanned. At this point I think it would be cheaper if I just bought the extra large 152-count box of Crayolas and made my own. :-)

The ruler shows what the driver gives it.  There's no ambiguity as to what the driver is doing with Qimage: just look above the preview page and Qimage will list "Page: " followed by the size of the page as defined by the driver.  23.766 is a typical width for an Epson using 24 inch paper if you don't have borderless enabled.

Regards,
Mike

I will watch the video after breakfast. :-) Although I 've already looked at most of the videos I could find.

Could be printer driver issues. I can't remember when we upgraded Q Image and when we purchased new Epson 9570 printer. The older version of Q Image had no problems, but we were also on a Epson 9880 Pro.

Question, what is the reason for the ruler at the top of the edit page, not showing 24 inch, or 36" etc. Whatever paper size is chosen. You can see the full ruler on the left.

Thanks,
George

It sounds like you are fighting the printer, driver, and what is physically possible when trying to print edge to edge especially on canvas.  This video covers all that:

https://youtu.be/15G1AWZTVwo

Instead of using 36 inch paper, why don't you just rotate the prints 90 degrees so that the 20 inch side prints on the 24 inch width and the 24 inch side prints on the length?  Even though that would leave 4 inches not used on the width, it gets rid of the myriad of issues that come with being forced to use borderless and trying to print exactly 24 inches on a 24 inch roll and the printer not being exact enough to do that.

Regards,
Mike

This topic has been moved to Qimage Ultimate.

https://ddisoftware.com/tech/index.php?topic=4696.0