Mike Chaney's Tech Corner
November 23, 2024, 08:49:28 PM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News: Qimage registration expired? New lifetime licenses are only $59.99!
 
   Home   Help Login Register  
Mike Chaney's Tech Corner > Mike's Software > Qimage Ultimate > Show a cut mark on edge ?
Pages: [1]
« previous next »
  Print  
Author Topic: Show a cut mark on edge ?  (Read 9702 times)
dannac
Jr. Member
**
Posts: 82
« on: October 06, 2019, 09:11:21 PM »
Show cut mark on image edge ?
Logged
Fred A
Forum Superhero
*****
Posts: 5644



WWW Email
« Reply #1 on: October 07, 2019, 10:19:13 AM »
Quote
Show cut mark on image edge ?
Sure, all set to use.
Use the Printers and settings tab.
Scroll down the right side ad find CUT MARKS.
Read the description by clicking the blue ball, and then select the one you want.
See snaps
Fred
Logged
admin
Administrator
Forum Superhero
*****
Posts: 4220



Email
« Reply #2 on: October 07, 2019, 02:40:37 PM »
What Fred said.  Wink  I'll only add that in your case, you should probably try Crop Marks (which extend outward from each corner) and Mark Corners (which bracket each corner against each print).  Not sure which you'd prefer.

Regards,
Mike
Logged
dannac
Jr. Member
**
Posts: 82
« Reply #3 on: October 07, 2019, 03:06:44 PM »
Great ... will have a look later.

Thanks for the reply's and photos.
Logged
Ernst Dinkla
Sr. Member
****
Posts: 410


Email
« Reply #4 on: October 07, 2019, 05:38:01 PM »
Quote from: dannac on October 07, 2019, 03:06:44 PM
Great ... will have a look later.

Thanks for the reply's and photos.

Add 0.5mm white borders + corner marks and cut just within the marks. That way you waste less paper and keep  marks on the printed image up to the last cut. Do not nest the images too close, cut becomes better with say at least a 2mm strip cut off.
Cutting marks that extend from the corner as used in the graphic industry have more sense when stacks of sheets are cut together on a guillotine cutter.

Ernst, op de lei getypt.
Logged
dannac
Jr. Member
**
Posts: 82
« Reply #5 on: October 07, 2019, 05:53:07 PM »
Thanks for the reply.

Looks like " guide borders " will work great.
Logged
Jules
Full Member
***
Posts: 124



Email
« Reply #6 on: October 26, 2019, 07:57:03 AM »
Quote from: admin on October 07, 2019, 02:40:37 PM
What Fred said.  Wink  I'll only add that in your case, you should probably try Crop Marks (which extend outward from each corner) and Mark Corners (which bracket each corner against each print).  Not sure which you'd prefer.

Regards,
Mike

I use these quite frequently. The only trouble is that when you make your first cut, you cut of the guides for the next (two) cuts. I don't think there is any way around this without having the guides on the cut print. I manage it by extending the mark in towards the print by a mm or two with a scalpel. So when I cut off the first edge, I can then see where to cut the next two from.
Jules
Logged
Ernst Dinkla
Sr. Member
****
Posts: 410


Email
« Reply #7 on: October 27, 2019, 08:19:26 AM »
Quote from: Jules on October 26, 2019, 07:57:03 AM
Quote from: admin on October 07, 2019, 02:40:37 PM
What Fred said.  Wink  I'll only add that in your case, you should probably try Crop Marks (which extend outward from each corner) and Mark Corners (which bracket each corner against each print).  Not sure which you'd prefer.

Regards,
Mike

I use these quite frequently. The only trouble is that when you make your first cut, you cut of the guides for the next (two) cuts. I don't think there is any way around this without having the guides on the cut print. I manage it by extending the mark in towards the print by a mm or two with a scalpel. So when I cut off the first edge, I can then see where to cut the next two from.
Jules

I suggest to read my other comment in this thread.

Ernst, op de lei getypt.
Logged
Jules
Full Member
***
Posts: 124



Email
« Reply #8 on: November 05, 2019, 08:18:48 AM »
OK, thanks
Jules
Ik begrijp het nu  Smiley
Logged
Fred A
Forum Superhero
*****
Posts: 5644



WWW Email
« Reply #9 on: November 05, 2019, 08:36:22 AM »
Quote
OK, thanks
Jules
Ik begrijp het nu 

Are you speaking Klingon?

"Live Long and Prosper"
Logged
Ernst Dinkla
Sr. Member
****
Posts: 410


Email
« Reply #10 on: November 05, 2019, 05:24:41 PM »
Quote from: Jules on November 05, 2019, 08:18:48 AM
OK, thanks
Jules
Ik begrijp het nu  Smiley

Mooi, hoef ik het niet in Klingon uit te leggen.

Ernst, op de lei getypt.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Security updates 2022 by ddisoftware, Inc.