Mike Chaney's Tech Corner
November 23, 2024, 07:47:45 AM *
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
News: Qimage registration expired? New lifetime licenses are only $59.99!
 
   Home   Help Login Register  
Mike Chaney's Tech Corner > Mike's Software > Qimage > NEWBIE NEEDS HELP
Pages: [1]
« previous next »
  Print  
Author Topic: NEWBIE NEEDS HELP  (Read 10189 times)
SMILING DOG
Guest
« on: August 26, 2009, 07:41:02 PM »
Hi to all, this is my first post and have many questions.  If I should post in the wrong topic, please direct me elsewhere. 

My first question is in regard to Epson driver and Qimage.  I have searched the posts and have not found the exact reference.  When I first purchased my 9880 I had a terrible time getting my large prints on roll paper to be the correct size.  They were always about .50 to 1" too short.  I finally managed to get a polite Epson tech who told me to set paper size to user defined as:  width = roll width, and length = length of desired print + 1 inch.  For the most part this has worked fine. 

My question is does this still apply when printing from Qimage?  When I set up the printer driver do I include the 1"? . 

I hope that made sense.

Thanks in advance.

Logged
Terry-M
The Honourable Metric Mann
Forum Superhero
*****
Posts: 3251



WWW
« Reply #1 on: August 26, 2009, 08:11:02 PM »
Hi Smiling Dog, welcome to the forum.
Quote
My question is does this still apply when printing from Qimage?  When I set up the printer driver do I include the 1"?
I'm not an expert on big printers but knowing something about how Qimage works, I'm pretty sure the answer is "yes".
Qimage does not "control" the driver but uses data from it.
Qimage gets it's page size,/printable area and "native" resolution data from the driver and is what you see above the page preview on the main screen.

It's important to set the printer driver from within Qimage so it is remembered by Qimage. That's the printer icon with the red flash, 3rd in from the right at the top of the main screen.
When you get a bit more familiar, we can help to explain how to save complete printer set set-ups printer settings, paper size & type, icc profile etc. for recall later.  Smiley
Terry.
Logged
SMILING DOG
Guest
« Reply #2 on: August 26, 2009, 10:23:41 PM »
Thanks Terry for your prompt response - I assumed that would be the correct answer, but before wasting more paper and ink I wanted to double check.  I have discovered the recall option and have opened the few jobs I had printed before reading Mike's "Wide Load" article regarding large prints and borderless expansion.  By comparing my recalled settings with his notes I did find a few options that were set incorrectly - so I think I am ready to give it a whirl ........

Thanks again!
Rhonda
Logged
Terry-M
The Honourable Metric Mann
Forum Superhero
*****
Posts: 3251



WWW
« Reply #3 on: August 26, 2009, 10:39:44 PM »
Quote
so I think I am ready to give it a whirl ........
I'm sure you'll be in a whirl of delight when you see the quality of your prints using Qimage   Cheesy
Terry.
Logged
SMILING DOG
Guest
« Reply #4 on: August 27, 2009, 01:08:53 AM »
#$@#!*!!  I just ran my print from Qimage and the color is great now, but the size is still off!!  What am I doing wrong?  I needed 18 x 24 and it comes out 18 x 22.25!!!  What is the problem??  Printing on 36" roll -page size is  user defined in printer driver at 36" x 19", centered on page in Qimage, custom size 18 x 24. 

If any body is out there please help me out, I really need to get this guy's print done.

Thanks!
Logged
SMILING DOG
Guest
« Reply #5 on: August 27, 2009, 03:07:43 AM »
 Grin  YAAAAAY!!!!!  I finally figured it out.  Sorry to have been so hysterical in my last post, I have been struggling with this all week long.  I found the link to the online user guide and figured out it was the cropping method I had selected.  Apparently my aspect ratio was off a bit and the crop method was checked to print the whole image instead of cropping to exact size.  Whew! It came out perfectly now. 

Thanks to all ........ good night.
Logged
Terry-M
The Honourable Metric Mann
Forum Superhero
*****
Posts: 3251



WWW
« Reply #6 on: August 27, 2009, 07:17:40 AM »
Quote
I finally figured it out.
Pleased to hear that  Grin
Quote
I needed 18 x 24 and it comes out 18 x 22.25!!!
A Tip:
You can check what size Qimage is going to print by looking at the queue data below the thumbnails, that tells you the size and whether borders are included. See a screen snap attached below.
You may need to click the panel title bar to open it.
Terry
« Last Edit: August 27, 2009, 09:50:36 AM by Terry-M » Logged
SMILING DOG
Guest
« Reply #7 on: August 27, 2009, 12:15:32 PM »
Oh, that is good to know.  I don't see the screen shot you mentioned, but I will see if I can find the information tonight when I get home. 

Have a great day!
Logged
Terry-M
The Honourable Metric Mann
Forum Superhero
*****
Posts: 3251



WWW
« Reply #8 on: August 27, 2009, 12:32:42 PM »
Quote
I don't see the screen shot you mentioned,
It's there at the bottom of my post Reply #6 as an attachment.
Click on it to get a larger view.
Terry.
Logged
SMILING DOG
Guest
« Reply #9 on: August 28, 2009, 01:26:42 PM »
Oh, OK I see it now, thanks.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Security updates 2022 by ddisoftware, Inc.