Show Posts
|
Pages: [1] 2 3 ... 8
|
4
|
Mike's Software / Qimage Ultimate / Re: Flash Card Copy Option
|
on: September 25, 2018, 01:53:27 AM
|
Mike,
(1) Let Flash Card Copy/Move develop them into JPEG's as part of the copying process (if that "Develop raw photos after they are copied/moved" setting is checked). (2) Don't check that option and just navigate to the raw photos folder and let the QU main UI develop the raws during the thumb building process.
I used both options. In option (2) there were 116 raw photos in Raw folder. When using option (1), during the developing phase the process got stuck on #113. See attachment. Bottom of screen in one line it states 97% and last line 113 of 116.
I checked the two sub-folders and found 116 in the Raw folder and only 113 in the Developed folder.
So, I noted the three missing images. Then I reopened QU and processed the three images. In other words, they were not corrupt in the Raw folder.
At this point, I'm not sure what is causing the Developing phase to get stuck at 113. So, when I shoot raw in the future I will use option (1) and see if it gets stuck. I will always have the Raw shots. But most likely, when the JPG camera setting when I shooting unless it is something special.
Thanks for your help.
Vlady
|
|
|
5
|
Mike's Software / Qimage Ultimate / Re: Flash Card Copy Option
|
on: September 24, 2018, 02:22:59 AM
|
Mike,
I'm using a Nikon D3300. I using Qimage Ultimate to copy the raw images to a folder on my computer. After all 116 photos are copied to my file the Qimage Ultimate then develops the images and saves them as JPGs. But it only does 113 of the Raw not the total 116.
The attached image in the above is not the setting. I've changed that when I made the correction you suggested the following:
[Operation: Copy File Type: Photos To Folder: C:\Photos
The above reads "Copy photos to C:\Photos".]
Tomorrow, when my eyes are less tired I will come back to this issue.
|
|
|
6
|
Mike's Software / Qimage Ultimate / New Problem with Flash Card Option
|
on: September 24, 2018, 01:06:45 AM
|
New Problem: Copying RAW shots to Raw Folder works, but when developing the Raw and Sending them to Developed Folder the process freezes.
For example I took 116 Raw shots of fireworks. The 116 shots were copied into the Raw Folder. However, when the Raw shots were being developed and saved as JPGs the program "stopped" developing or was stuck at 113--the program was still operating and the symbol showing the processing was still going on was spinning, but nothing was happening even when I let the program run for ten more minutes. So, I had to stop the program. When I checked the folders there were 116 Raw photos in the Raw Folder, but only 113 photos in the Developed Folder.
By the way I tried Copying and Developing several times. I even shut the computer off. Still the same thing. I'm at my wit's end.
When I processed this card in July on an earlier Qimage 2018 all an smoothly.
Any help is welcome.
Vlady
|
|
|
8
|
Mike's Software / Qimage Ultimate / Flash Card Copy Option
|
on: September 22, 2018, 09:37:07 PM
|
I purchased a new HP computer with Windows 7. I have installed QImage 218.125 I am trying to get the Flash Card Copy Option to function. All I get is a Nothing To Do response. I have spent at least 3 hours trouble shooting with no success. What am I doing wrong?
See the two screen shots.
Thanks, Vlady
|
|
|
12
|
Mike's Software / Qimage Ultimate / Re: Installing QUimage
|
on: February 28, 2017, 02:46:11 AM
|
Fred,
Today I used QUimage twice. The first time that I used it I had the restart it by pressing the Shift key. The second time QU loaded just like it used to. I guess the trick is to remember the Shift key when the error message comes up.
Thanks again.
Vlady
|
|
|
14
|
Mike's Software / Qimage Ultimate / Re: Installing QUimage
|
on: February 25, 2017, 09:09:29 PM
|
Fred,
I haven't done anything with the printer. In fact, I don't use it very often. I will add that I had tried to install each of the versions of QU, i.e., 106 and 119, with Defender disabled. Also, I uninstalled my copies of QU before I did a new install.
There is something else, I remember seeing a message from QU suggesting that I should not use QU as an administrator. I know that once--a long time ago--I did use QU as an administrator, but I have done that recently. I've searched through Windows Control Panel and other Windows folders to find administrator, but I have failed to locate.
I don't know if this helps.
Vlady
|
|
|
|