Show Posts
|
Pages: 1 2 [3] 4 5 ... 8
|
31
|
Mike's Software / Qimage Ultimate / Re: Problem Saving Images
|
on: September 20, 2014, 10:05:43 PM
|
Thanks Mike,
Earlier I tried to find the junk but couldn't.
However, here's an interesting development. I went out and shot with my Nikon D40. I downloaded all the images using QU as I usually do. Then pp'd three images in PSE 9. Went back to QU, sharpened them, and saved them. There was no problem.
So, I went back to the Canon S90 and shot RAW. Then downloaded them and let QU develop them. The developed jpgs were processed smoothly. Then I pp'd several of them, saved them, opened QU, sharpened them. Voila, no problems.
My tentative conclusion is that when I shoot with the S90 in jpg the problem arises. Not sure why?
By the way, I went over to jpg in the S90 because I had problems processing the developed jpgs. It seems that certain colors just didn't come out right.
The long and the short of it: You've made changes to QU and I'll see what happens then. I seem to have narrowed the problem to the S90 in jpg only. I'll try to find out what I can, but no promises because I'm not that good at some of this.
edit: I did more experiments S90 jpgs. The original S90 jpgs have no problems in QU. The problems occur when I adjust them in PSE 9.
Thanks again to you and Fred for all your help.
Vlady
|
|
|
32
|
Mike's Software / Qimage Ultimate / Re: Problem Saving Images
|
on: September 20, 2014, 04:26:22 PM
|
Fred,
Thanks for this information. I'll check out what you suggested. I may have to reload PSE 9--we'll see. I have been thinking of getting PSE 13 when it comes out.
Yes, the photo is much better.
Will wait to see what Mike figures out.
Best,
Vlady
|
|
|
33
|
Mike's Software / Qimage Ultimate / Re: Problem Saving Images
|
on: September 20, 2014, 02:21:23 AM
|
Fred and Mike,
Sorry that I didn't respond earlier, but it was a hectic day.
1. I went back, selected one jpg image that I had post processed with PS Elments 9, sharpened it, and tried to save it via Done command and Create new image as jpg.
2. The same error appeared.
3. I cancelled out. The image, interestingly, was saved as in the past. It always stopped with the first image when I was doing batch.
What I going to do is send Fred three images: the original jpg, the PSE processed jpg; and then the OU sharpened and seemly saved jpg image.
Your help is appreciated.
Best,
Vlady
|
|
|
34
|
Mike's Software / Qimage Ultimate / Problem Saving Images
|
on: September 19, 2014, 03:07:46 AM
|
I have a problem saving images that I have sharpened in QU using batch.
1. This problem emerged toward the end of the v 2014. 2. The problem doesn't occur when I sharpen images straight out of the camera. 3. However, it does occur when I process them in PS Elements 9 and save them under a new name. 4. I load the modified images into a queue in Qimage Ultimate. 5. Sharpen the first, then press Done. 6. In the new window I apply the changes to all images and select Create New Images and press OK/ 7. Then after a passage of time I get the screen with the image below.
I can't figure out what is happening
Any help will be appreciated.
|
|
|
36
|
Mike's Software / Qimage Ultimate / Re: v2014.250 issues/comments
|
on: August 08, 2014, 12:55:03 AM
|
I tried the 2014.250 revised DFS sharpening. I had sharpened a couple of jpgs with an earlier version. I thought that I wouldn't see the difference. I was surprised by the difference, and what an improvement.
Thanks load Mike.
|
|
|
37
|
Mike's Software / Qimage Ultimate Challenges / Re: Challenge # 27 Match your Mat!
|
on: May 04, 2014, 01:15:51 AM
|
Terry,
Your last reply solved my problem. By avoiding the template in the first place, I've been able succeed every time.
I don't know why I have such trouble dragging an image to the template and have it appear, but I do.
Now I don't have to even think about the template.
Thanks for your advice.
Best,
Vlady
|
|
|
38
|
Mike's Software / Qimage Ultimate Challenges / Re: Challenge # 27 Match your Mat!
|
on: May 03, 2014, 01:52:53 AM
|
greetings,
I've continued to experiment and learn more about matting with QI. However, I wonder if I'm still doing something wrong.
I have a problem of placing an image on the template. Here is my procedure: 1) check that I have free-style 2) click on template and then drag it over free style 3) go to image and drag it to the template.
It can take 7 or more drags of image to template before the image actually pops in. I do clear queue and start the sequence over each time.
Can't figure out what I'm doing wrong. Struggling with this for a couple of days.
Anyone else having this problem?
Thanks,
Vlady
|
|
|
40
|
Mike's Software / Qimage Ultimate Challenges / Re: Challenge # 27 Match your Mat!
|
on: April 27, 2014, 03:06:31 AM
|
Fred and Terry,
Thanks for all the help. I think that I have the knack of it, but will have to practice more.
I'm especially glad to the instructions about "print to file" because this is my usual procedure. I print files either on campus or through a commercial printer.
Here are two different photos of the dancer. This is the 3rd try for attachment and I hope I have them small enough this time.
Again, thanks,
Vlady
|
|
|
41
|
Mike's Software / Qimage Ultimate Challenges / Re: Challenge # 27 Match your Mat!
|
on: April 26, 2014, 03:29:38 PM
|
Terry,
Thanks for your information. I will go back and work on it and let you know how I succeed.
I'm still puzzled how I was lucky once and got a jpg.
Thanks for the comments on the photo. It was taken in a "cultural restaurant" in Siem Reap, Cambodia, when visiting Ankgor Wat.
Again, thanks loads.
Vlady
|
|
|
42
|
Mike's Software / Qimage Ultimate Challenges / Re: Challenge # 27 Match your Mat!
|
on: April 26, 2014, 01:23:47 AM
|
Fred,
But for your "challenge", I wouldn't have bothered with borders.
I watched and listened to the two videos and tried. I've had some fun. But I was able to save it once. Never again have I been able to save. I don't know what I did to save and I can't find the instructions.
Best,
Vlady
|
|
|
|